
A gas tankless water heater heats water only when you open a tap, so it skips the standby loss of a storage tank. Its performance depends on three things: whether it is condensing or non-condensing, whether its venting and gas supply match the unit's rated input, and whether it runs on natural gas or propane. Getting those right at installation is the first step.
How a gas tankless water heater works
A burner heats water as it flows through a heat exchanger, so the unit fires only when you draw hot water. Nothing sits in a tank, which means the limit is how fast the unit can heat water rather than how much it holds. According to the U.S. Department of Energy, water heating is about 18% of a home's energy use, so efficiency is worth a close look.
Matching flow to your household
The key number is Maximum GPM, which the federal test procedure defines as the maximum gallons per minute of hot water a tankless unit can supply. For comparison, federal maximum flow rates are 2.5 gallons per minute at 80 psi for showerheads and 2.2 gallons per minute at 60 psi for lavatory and kitchen faucets. List the fixtures that might run together, add up their flow, and compare the total with the unit's rating.
Ratings assume a specific temperature rise, so a unit that looks adequate on paper can fall short when incoming water is colder. Ask your installer to check the rating against your local incoming water temperature and the setting you plan to use.
Condensing vs non-condensing units
A non-condensing unit exhausts hot combustion gases at a high temperature, so it uses metal venting built for that heat. A condensing unit recovers more heat from those gases. The exhaust cools enough that water vapor condenses into acidic condensate, which must drain away safely. Condensing models generally reach higher efficiency, and the ENERGY STAR minimum Uniform Energy Factor (UEF) for gas tankless water heaters is 0.95. UEF is the federal measure of a water heater's overall efficiency, so compare each model's rated UEF against that line.
| Feature | Non-condensing | Condensing |
|---|---|---|
| Exhaust temperature | Higher | Lower after heat recovery |
| Vent material | Metal, as the manufacturer specifies | Plastic, as the manufacturer specifies |
| Condensate drain | Not required | Required |
| Retrofit into older homes | Often simpler | Often needs new venting and a drain route |
Venting materials and layout
The vent carries combustion gases outdoors, and it must use the material the manufacturer lists for that model. Condensing units typically use plastic venting such as PVC, CPVC or polypropylene, while non-condensing units use metal. Never substitute a cheaper or more convenient pipe, because a mismatched vent can fail under heat or leak combustion gases into the home.
Layout matters as much as material. Keep runs as short and direct as the manual allows, use only the fittings it lists, and follow its slope requirements so condensate flows back to the drain. Termination location, clearance from windows and air intakes, and combustion air supply are set by the manual and by local rules.
Common venting mistakes
- Reusing an old flue or liner that the manufacturer has not approved for the unit.
- Reducing vent diameter to fit a tight space.
- Adding elbows the manual does not allow.
- Draining condensate without a proper trap or termination.
- Sharing a vent with another appliance without the installer confirming it is allowed.
Gas line capacity
Each unit has a rated gas input, usually listed in BTU per hour on the data plate and in the manual. The gas line and meter must deliver that flow at the pressure the unit needs while other gas appliances are running. An undersized line can starve the burner, which may show up as reduced output, error codes or shutdowns during heavy use.
Pipe diameter, total length, fittings, the meter, the regulator and every other gas appliance on the line all affect capacity. Sizing is a calculation, not a guess. The method and permit requirements vary by state and city, so check with your local building department before any work begins.
What to gather before the installer arrives
- Write down the BTU per hour input rating from the unit's data plate.
- List every gas appliance on the same line, such as a furnace, range, dryer or fireplace, with each rated input.
- Note the pipe diameter and where the meter and shutoff are located.
- Ask your utility or propane supplier about the supply pressure you receive.
Natural gas vs propane
A gas tankless water heater is built for one fuel. Natural gas and propane burn differently and operate at different pressures, so the burner and gas valve are set for the fuel you have. Some manufacturers offer a conversion kit, which should be installed exactly as the manufacturer specifies and checked by a qualified installer.
Propane packs more energy into each cubic foot than natural gas, so a fuel switch is never a simple swap. Propane also means a tank on your property and scheduled fills, while natural gas arrives through a utility line. Weigh supply reliability, tank space and fuel cost alongside the unit's rating when you compare options.
Maintenance that keeps it running
According to the U.S. Department of Energy, tankless water heaters can last more than 20 years. That assumes steady maintenance, correct venting and an adequate gas supply. Follow the maintenance schedule in your manual, and use this checklist between service visits.
- Clean the inlet water filter screen, which traps sediment before it reaches the heat exchanger.
- Descale the heat exchanger on the manual's schedule, using a method the manufacturer approves. This matters most in hard water areas.
- Inspect the outdoor vent terminal for debris, nests, ice or blockage, and look for soot or staining near the vent.
- On a condensing unit, confirm the condensate drain flows freely and its trap stays full.
- Write down any error codes before resetting the unit, so a technician can see the pattern.
- Confirm the temperature setting. The DOE recommends 120°F for most households.
Legionella bacteria can grow in water heaters under certain conditions. DOE recommends a tempering (mixing) valve set to 120°F downstream of storage tanks. A tankless unit does not store water in a tank, so ask your installer how your system addresses Legionella risk and whether a tempering valve belongs in your plan.
Safety first
If you smell gas, leave the home and call the gas utility or 911 from outside. Install carbon monoxide alarms on every level of the home and outside sleeping areas, as the CPSC recommends. Hot water burns quickly: according to the CPSC, third-degree burns can occur after about 6 seconds at 140°F and about 30 seconds at 130°F, and can even occur after 5 minutes at 120°F. The CPSC recommends setting water heaters to 120°F, while the DOE notes that people with a compromised immune system or chronic respiratory disease may want to keep the setting at 140°F, so talk with a doctor before you change it.
When to call a professional
Some problems need hands-on diagnosis from a qualified gas and plumbing professional. Arrange a visit if you notice any of the following.
- The unit shuts off during normal use or never reaches the temperature you set.
- Error codes return after you clear them.
- You see soot, scorching or staining near the vent or the unit.
- Condensate pools, leaks or freezes at the drain on a condensing model.
- Output drops whenever a second gas appliance runs.
- Water leaks from the unit or its connections.
Rebates and tax credits to check
Federal and state incentives change, so confirm each one on the official site before you plan a purchase. According to the IRS, as checked on November 19, 2026, the 25C Energy Efficient Home Improvement Credit (up to $600 for qualifying gas, propane or oil water heaters) applied only to property placed in service before December 31, 2025, so it does not apply to 2026 installations. The 25D Residential Clean Energy Credit is not available for property placed in service after December 31, 2025.
DOE Home Electrification and Appliance Rebates (HEAR) are run by states and available only in select states. They cover up to $1,750 for an ENERGY STAR heat pump water heater for households with income below 150% of area median income. Since DOE Program Notice 26-2 (effective May 29, 2026), these rebates no longer cover replacing a gas appliance, only electric-to-more-efficient-electric upgrades. Check your state energy office and your utility for current programs.
Finding a qualified installer
Get at least two written quotes, and make sure each one describes the same work. Check the contractor's license with your state licensing board where licensing applies. Ask who pulls the permit and schedules the inspection. Then ask what the quote includes: haul-away of the old unit, any code upgrades to venting or the gas line, and whether the installer registers the warranty for you.
Frequently asked questions
Should I choose a condensing or non-condensing gas tankless water heater?
Choose condensing if you want higher efficiency and your home can support plastic venting and a condensate drain route. Choose non-condensing if your existing metal venting is suitable and adding a drain is impractical. In either case, the ENERGY STAR minimum UEF for gas tankless water heaters is 0.95, so compare each model's rating against that line. Have the installer confirm the vent route and drain before you commit.
Can a gas tankless water heater run on propane if it was set up for natural gas?
Not by simply changing a setting. Natural gas and propane operate at different pressures, so the burner and gas valve are set for one fuel. Some manufacturers offer a conversion kit, but it should be installed exactly as the manufacturer specifies and checked by a qualified installer. Also confirm that your gas line still has enough capacity for the fuel you will use.
How long does a gas tankless water heater last?
According to the U.S. Department of Energy, tankless water heaters can last more than 20 years, while most storage tank water heaters last 10 to 15 years. Actual life depends on water quality, regular maintenance, and correct venting and gas supply from the start. Keep records of each service visit so you can show a technician or a future buyer how the unit was cared for.
How do I know if my gas tankless water heater has enough flow?
Add up the flow of the fixtures you expect to run together, then compare that total with the unit's Maximum GPM. Federal maximum flow rates of 2.5 gallons per minute at 80 psi for showerheads and 2.2 gallons per minute at 60 psi for faucets give you a baseline. Ask your installer to check the rating against your incoming water temperature, because colder water reduces the flow a unit can deliver at your set temperature.
What maintenance can I handle myself on a gas tankless water heater?
Cleaning the inlet filter, checking the outdoor vent for blockages, recording error codes and confirming the drain on a condensing model are reasonable owner tasks. Descaling should follow the manufacturer's procedure, and some models make it an owner task. Work on the gas connections, burner or venting belongs to a qualified installer, and any repair that involves those parts should wait for one.