
The cost to run a water heater depends on how much energy it uses each year and what that energy costs locally. You can estimate it from the yellow EnergyGuide label: multiply the yearly energy figure by your local electricity or natural gas rate. The operating cost calculator on this site can run the math with your own rates.
What the cost to run a water heater includes
Running cost is the energy the unit consumes to heat water, multiplied by what you pay for that energy. Part of that energy is standby loss, the heat that escapes from a storage tank even when nobody is using hot water. How much hot water your household draws matters as much as the unit itself.
According to the U.S. Department of Energy, water heating is about 18% of a home's energy use. That makes it worth measuring rather than guessing. Four inputs drive the result:
- Yearly energy use, in kilowatt-hours (kWh) for electric units or therms for gas units
- Your local rate, per kWh or per therm, taken from a recent utility bill
- Your hot water use, including showers, dishwasher and laundry loads, and faucet use
- The unit's efficiency, measured by its Uniform Energy Factor (UEF)
Reading the yellow EnergyGuide label and UEF
New water heaters carry a yellow EnergyGuide label that shows an estimated yearly energy use and an estimated yearly operating cost. The energy figure is the part you can reuse with your own rate. The dollar estimate on the label is based on a standard test and an assumed rate, so it is useful for comparing models, not for predicting your bill.
The federal test procedure (10 CFR 430, Appendix E) defines the Uniform Energy Factor as the measure of a water heater's overall efficiency. A higher UEF means more of the energy you buy ends up as hot water. Two other test terms describe capacity rather than cost: the First-Hour Rating for storage tanks, which estimates the maximum volume of hot water the unit can supply within an hour starting fully heated, and the Maximum GPM for tankless units, which is the maximum gallons per minute it can supply.
Capacity affects cost indirectly. A tank much larger than your household needs holds more water at temperature and loses more heat over time, so match the unit to your actual use.
How to estimate your annual energy cost step by step
- Find the yearly energy use. Locate the yellow EnergyGuide label or the unit's rating data. Write down the estimated yearly energy use in kWh for electric models or in therms for gas models.
- Get your local rate. On an electric bill, find the price per kWh. On a gas bill, find the price per therm. If your gas bill uses hundreds of cubic feet (Ccf) or cubic feet, use the conversion printed on the bill to get therms.
- Multiply the units. Annual kWh multiplied by the rate per kWh gives an estimated yearly electricity cost in dollars. Annual therms multiplied by the rate per therm gives an estimated yearly gas cost in dollars.
- Check against national reference points. The U.S. Energy Information Administration (EIA) reports an average US residential electricity price of 18.19 cents per kWh for January to August 2026, and an average residential natural gas price of $15.34 per thousand cubic feet in 2025, about $1.48 per therm. Compare your local rate with these figures to see whether your area runs higher or lower.
- Run the numbers with your own inputs. Use the operating cost calculator on this site to repeat these steps with your label figure and your rate, then compare the result with a full year of your bills.
The EIA averages show the arithmetic, not a forecast. For example, 1,000 kWh multiplied by 18.19 cents equals $181.90, and 100 therms multiplied by $1.48 equals $148. Your result depends on your own label figure and your own rate.
Gas, electric and heat pump models compared
The fuel type changes which unit and which rate you multiply, so compare each model using its own label. The table below shows what to read on each.
| Type | What the label reports | What to multiply by | What affects running cost |
|---|---|---|---|
| Gas storage | Estimated yearly energy use in therms | Your natural gas rate per therm | Efficiency rating, tank size, hot water use |
| Electric storage | Estimated yearly energy use in kWh | Your electricity rate per kWh | Heat loss from the tank, hot water use |
| Heat pump | Estimated yearly energy use in kWh | Your electricity rate per kWh | Its higher efficiency rating, and the air temperature around the unit |
A heat pump water heater moves heat from the surrounding air into the water rather than making all the heat directly. Because its output depends on the air around it, the room where it sits matters. Gas units need venting and their own fuel supply, which affects installation cost more than running cost.
Tankless units heat water on demand, so they do not carry standby loss the way a tank does. Their running cost still depends on how much hot water you draw and on the rate you pay.
Lower the energy your water heater uses
The cheapest kilowatt-hour or therm is the one you do not use. Start with the water temperature and the fixtures that draw hot water.
- Set the temperature to 120°F. According to the U.S. Department of Energy, 120°F is a temperature considered safe for most of the population. People with a compromised immune system or chronic respiratory disease may want to keep it at 140°F, so ask your doctor whether that applies to your household.
- Choose fixtures within federal flow limits. Under DOE rules (10 CFR 430.32), showerheads are limited to 2.5 gallons per minute (GPM) at 80 psi, and lavatory and kitchen faucets to 2.2 GPM at 60 psi. Fixtures at or below these maximums draw less hot water per minute.
- Fix hot water leaks. A dripping hot faucet draws heated water all day, so repair it promptly.
- Insulate exposed hot water pipes. Insulation reduces heat loss between the tank and the tap, so less water has to be reheated.
Safety first: water temperature and scalding
Hot water can cause serious burns quickly. According to the U.S. Consumer Product Safety Commission (CPSC), third-degree burns can occur after about 2 seconds at 150°F, about 6 seconds at 140°F, and about 30 seconds at 130°F, and they can occur after 5 minutes at 120°F. Lowering the setting to 120°F reduces both the scald risk and the energy used to keep the tank hot.
Rebates and tax credits change quickly
Based on official sources checked on November 19, 2026, these programs apply as follows:
- 25C Energy Efficient Home Improvement Credit: up to $2,000 a year for heat pump water heaters, and up to $600 for qualifying gas, propane or oil water heaters. It applied only to property placed in service before December 31, 2025, so it does not apply to 2026 installations.
- 25D Residential Clean Energy Credit: 30%, including solar water heaters. It is not available for property placed in service after December 31, 2025.
- DOE Home Electrification and Appliance Rebates (HEAR): run by states and available only in select states. Up to $1,750 for an ENERGY STAR heat pump water heater, for households with income below 150% of area median income. Since DOE Program Notice 26-2 (effective May 29, 2026), these rebates no longer cover replacing a gas (non-electric) appliance, only electric-to-more-efficient-electric upgrades.
Confirm current details on the IRS and DOE websites, and check your state energy office and your utility for current programs before you buy.
What installation and replacement add to the total
Installation and replacement costs sit on top of running costs, and this guide does not publish dollar figures for them. The main components are the unit itself, labor, permits, any venting or gas line work, electrical circuit changes for electric and heat pump models, haul-away of the old tank, and code upgrades. Check with your local building department for the permit and code requirements that apply where you live, since they vary by state and city.
Lifespan changes the math. According to the U.S. Department of Energy, most storage tank water heaters last 10 to 15 years, while tankless water heaters can last more than 20 years. Divide the installed cost by expected years of service to compare options fairly.
For gas models, the CPSC recommends carbon monoxide alarms on every level of the home and outside sleeping areas. Test them on a regular schedule.
How to compare quotes for a new or replacement unit
Get at least two written quotes for the same unit size, fuel type and scope of work, so you can compare them line by line. Check each contractor's license with the state licensing board where licensing applies. Ask who pulls the permits, and whether the price includes haul-away, any code upgrades and warranty registration. A quote that leaves out these items is not finished, even if the total looks lower.
Frequently asked questions
Is the EnergyGuide estimate the same as what I will pay?
No. The yellow label estimate comes from a standard test, not from your household's hot water use, temperature setting or local rate. It works best for comparing units side by side. For a closer figure, take the yearly energy use from the label, multiply it by your rate from a recent bill, and compare the result with your past bills for the same season.
Which is cheaper to run, gas or electric?
The answer depends on your local rates as much as on the fuel type. Compare each unit's yearly energy figure, then multiply by the price you actually pay per kWh or per therm. The EIA averages in this guide are national reference points only: 18.19 cents per kWh for January to August 2026, and about $1.48 per therm based on the 2025 gas average.
What temperature should I set my water heater to?
According to the U.S. Department of Energy, 120°F is considered safe for most of the population, and the CPSC also recommends 120°F. People with a compromised immune system or chronic respiratory disease may want 140°F, so ask your doctor if that applies. A lower setting also reduces the heat your tank loses over time.
Can I still claim a federal tax credit for a water heater installed in 2026?
Based on official sources checked on November 19, 2026, the 25C credit applied only to property placed in service before December 31, 2025, so it does not apply to 2026 installations. The 25D credit is also unavailable for property placed in service after that date. State-run HEAR rebates exist only in select states, so check your state energy office and your utility, and confirm details on the official IRS and DOE sites.
Which usage figure should I use if my electric bill changes by season?
Use the average price per kWh from your last twelve months of bills rather than a single month. If your utility uses tiered or time-of-use pricing, the average you actually pay per kWh is the figure to use for a rough estimate. Ask your utility whether it offers a separate rate or meter for water heating before you finalize your numbers.
How often should I recheck my running cost?
Recheck it after any change that affects use or price, such as a new fixture, a change in household size, a new utility rate, or a new unit. Comparing a year of bills before and after the change shows whether the savings you expected actually appeared. Re-run the calculation on the same inputs each time so the results stay comparable.