The Water Heater Guide

Sizing & efficiency

Tankless Water Heater Sizing: GPM and Temperature Rise

Updated November 19, 2026By the The Water Heater Guide editorial team
What size tankless water heater do i need

If you are asking what size tankless water heater do I need, the answer comes down to two numbers: required flow in gallons per minute (GPM) and temperature rise. Required flow is the total GPM of the fixtures you run at the same time. Temperature rise is your desired hot water temperature minus the incoming groundwater temperature.

What Size Tankless Water Heater Do I Need for Your Home?

Sizing a tankless unit works differently from sizing a tank. A storage tank is compared with its First-Hour Rating, the estimate of how much hot water it can supply in the first hour starting fully heated. A tankless unit heats water as it flows, so its limit is its Maximum GPM, the most gallons per minute of hot water it can supply under the federal test procedure (10 CFR 430, Appendix E).

The job is a matching exercise. Figure out how much hot water must flow at once, figure out how much heating your incoming water needs, and then find a unit that delivers that flow at that rise.

Step 1: Measure the Flow You Actually Need

Start with the fixtures you would run together on a busy morning. According to the U.S. Department of Energy (DOE), federal maximum flow rates for new fixtures are 2.5 gallons per minute at 80 psi for showerheads and 2.2 gallons per minute at 60 psi for lavatory and kitchen faucets. These limits are a useful starting point.

Check the fixtures you already have

Older fixtures often flow more than current limits, and a replacement showerhead can change your numbers. Look for a GPM marking on the fixture or its packaging. If nothing is marked, measure it.

  1. Place a container of known volume, such as a labeled one-gallon jug, under the faucet or in the shower stream.
  2. Run the fixture at the pressure you normally use, and time how long it takes to fill the container.
  3. Divide the gallons by the minutes. For example, 2 gallons filling in 40 seconds is 3 GPM, because 40 seconds is about 0.67 minutes.
  4. Repeat for each fixture you might use at the same time, and write down the results.

Add up the fixtures that overlap

Required flow is the sum of the fixtures used at the same time. A common morning might include one shower, one kitchen faucet and one bathroom sink. Using the federal limits as a guide, that is 2.5 + 2.2 + 2.2 = 6.9 GPM. Replace those numbers with your measured figures.

Count realistic overlaps, not every fixture in the house. A dishwasher or washing machine adds flow only if it runs during your shower or sink use in your normal routine. Two bathrooms raise the chance of overlap, so list the worst combination you expect.

Step 2: Determine Your Temperature Rise

Temperature rise is how much the unit must raise incoming water to reach your set temperature. The DOE and the Consumer Product Safety Commission (CPSC) both recommend setting water heaters to 120°F, which the DOE describes as a temperature considered safe for most of the population. For most homes, 120°F is the target.

Use this formula: desired temperature minus incoming temperature equals temperature rise. For a hypothetical example, 120°F water from 50°F incoming water is a rise of 70°F. Your numbers will differ.

Higher rises reduce flow. A unit that delivers its rated GPM at a modest rise may deliver noticeably less at a larger one, so the same unit can suit one house and fall short in another.

Safety first: Hot water causes serious burns. According to the CPSC, third-degree burns can occur after about 2 seconds at 150°F, 6 seconds at 140°F, 30 seconds at 130°F, and can occur after 5 minutes at 120°F. If you use a higher setting, ask your installer about a thermostatic mixing valve at showers and tubs.

When a household needs a higher setting

The DOE notes that people with a compromised immune system or chronic respiratory disease may want to keep the water heater at 140°F. A 140°F setting means a larger rise, so the same unit delivers less flow. Size for that rise, and expect you may need a larger model or more than one unit.

How Groundwater Temperature Changes Your Sizing

Incoming temperature is the temperature of the water reaching your heater from the utility or well. It varies by region and by season. Groundwater generally runs colder in northern areas and in winter, and warmer in southern areas and in summer. Colder incoming water means a larger rise and less flow from the same unit.

Find your coldest incoming temperature

Size for the coldest season, not the average. Your water utility is the best source for seasonal information, and you can also measure it yourself.

  1. On a cold morning, run the cold kitchen tap until the flow is steady.
  2. Fill a glass, place a thermometer in it, and read it once the reading settles.
  3. Repeat in a warm month to see how much the temperature changes.
  4. Use the lowest winter reading as your incoming temperature.

Regional patterns to keep in mind

In a cold climate, expect the largest rise in winter, when the heater works hardest. In warmer areas, the rise may be smaller most of the year, which can allow more flow. Test in winter anyway, because a unit sized only for summer can run short when you need it most.

How to Read a Unit's Flow Chart

Manufacturers publish flow charts showing the GPM a unit delivers at different temperature rises. The chart tells you more than the headline number on the box.

  1. Check the rating conditions printed with the chart, including the inlet temperature and the rise used for the headline flow.
  2. Find the rise that matches your coldest incoming temperature and your set temperature.
  3. Read across to the GPM the unit delivers at that rise.
  4. Compare that GPM with your required flow from Step 1.
  5. If the rated flow falls short, consider a larger unit, a second unit for a distant bathroom, or a different setting if the household allows it.

For gas units, flow is tied to the heater's input rating in BTU per hour. A higher input generally supports more flow at a given rise, so two units with similar headline GPM can perform differently at your site. Electric units are rated in kilowatts and often need a dedicated circuit, which a professional should check.

FactorEffect on the unit you need
Higher set temperatureLarger rise, so less GPM from the same unit
Colder winter groundwaterLarger rise in winter, so size for that season
More fixtures used at onceHigher required GPM
Higher BTU input on a gas unitGenerally more flow at a given rise

Efficiency, Lifespan and Incentives

Efficiency is measured by the Uniform Energy Factor (UEF), the federal measure of a water heater's overall efficiency. ENERGY STAR sets a minimum UEF of 0.95 for gas tankless units. According to the DOE, water heating is about 18% of a home's energy use, and tankless units can last more than 20 years, while most storage tanks last 10 to 15 years.

Incentives to confirm before you buy

Incentives change, so confirm current rules on the official IRS and DOE websites. As of November 19, 2026, the federal 25C Energy Efficient Home Improvement Credit applied only to property placed in service before December 31, 2025, so it does not apply to 2026 installations. The 25D Residential Clean Energy Credit is not available for property placed in service after December 31, 2025.

DOE Home Electrification and Appliance Rebates are run by states and available only in select states. Since DOE Program Notice 26-2 (effective May 29, 2026), they no longer cover replacing a gas appliance. Check your state energy office and your utility's website, because utility rebates vary.

Common Sizing Mistakes to Avoid

  • Sizing for one fixture instead of the overlap you actually see.
  • Using the headline Maximum GPM instead of the flow at your temperature rise.
  • Testing incoming water only in summer.
  • Ignoring plans to add a bathroom or a higher-flow fixture later.
  • Assuming two units with the same GPM rating perform the same at your site, since gas capacity and electrical supply differ.

When to Call a Professional

A chosen unit only performs as rated if the gas line, venting, electrical service and water pressure support it. If you smell gas, leave the home and call the gas utility or 911 from outside. The CPSC recommends carbon monoxide alarms on every level of the home and outside sleeping areas, which is worth confirming with any gas unit.

Finding a Pro for the Installation

Get at least two written quotes that describe the same unit and flow rating. Check the contractor's license with the state licensing board where licensing applies. Ask about permits and who pulls them, and check with your local building department, since requirements vary by state and city. Ask what is included, such as haul-away of the old unit, code upgrades and warranty registration.

Frequently asked questions

Can one tankless unit run a shower and a dishwasher at the same time?

It depends on the unit's flow at your winter temperature rise. Add the shower's measured GPM to the dishwasher's water use during the same period, then compare the total with the unit's rated GPM at that rise. If the total is close to or above the rating, expect reduced flow at peak times, or consider a larger unit.

Why does a tankless unit deliver less hot water in winter?

Colder incoming groundwater means the unit must add more heat to reach the same setting, which is a larger temperature rise. At a larger rise, the unit delivers fewer gallons per minute than its headline rating. Size the unit using the coldest incoming temperature you measured, and check the flow chart at that rise.

Should I size my tankless water heater for a 140°F setting?

Size for 140°F only if someone in the home has a compromised immune system or chronic respiratory disease, since the DOE notes they may want that setting. Otherwise, the DOE and CPSC recommend 120°F. At 140°F the unit delivers less flow, so plan for a larger model or more than one unit, and talk with a health care provider if you are unsure.

Does a second bathroom mean I need a bigger unit?

Often it does, because a second bathroom raises the chance that two fixtures run at the same time. Measure each fixture, then add the combinations you expect on a busy morning. Compare that total with the unit's rated GPM at your winter rise. If the total is higher, consider a larger unit or a separate small unit for the distant bathroom.

Are rebates still available for a gas tankless water heater installed in 2026?

Federal rules changed. As of November 19, 2026, the 25C credit applies only to property placed in service before December 31, 2025, and the 25D credit is not available after that date. DOE HEAR rebates no longer cover replacing a gas appliance since DOE Program Notice 26-2 took effect May 29, 2026. Check your state energy office, your utility and the IRS and DOE websites.

Need a pro? See businesses that install and repair water heaters in your metro area. Ask for at least two written quotes and check the contractor's license with your state where it applies.