What is a first hour rating?
A first hour rating is the federal estimate of the maximum volume of hot water a storage (tank) water heater can supply within one hour, starting from a fully heated tank. The rating is listed on the unit's label, and you compare it with your household's peak-hour hot water demand to judge whether a tank is large enough.
What the number actually measures
The first-hour rating comes from the federal test procedure in 10 CFR 430, Appendix E. The test starts with the tank full of hot water and measures how much hot water the unit can deliver during the first hour of heavy use. That captures both the stored hot water and the heat the unit adds while you are drawing from it.
It is not the same as the tank's gallon capacity. Two tanks with the same nominal size can have different first-hour ratings because of how quickly each one heats water. The rating tells you what the heater can do during your busiest hour, which is what you feel as a cold shower or an empty tub.
Do not confuse the first-hour rating with the Uniform Energy Factor (UEF). The UEF measures overall efficiency, while the first-hour rating measures capacity. A unit can be efficient and still too small for your household, or large and inefficient. You need both numbers when you compare models.
How to use the rating for a tank heater
- Find the first-hour rating on the label of the existing or proposed unit.
- List every hot water use that happens in your busiest hour. Common examples are showers, a dishwasher run, a washing machine on hot, and kitchen or bathroom sink use.
- Estimate the hot water each use takes. Federal maximum flow rates help here: according to the U.S. Department of Energy, showerheads are limited to 2.5 gallons per minute at 80 psi, and lavatory and kitchen faucets to 2.2 gallons per minute at 60 psi. A 10-minute shower at the maximum flow uses up to 25 gallons of mixed water, part of it hot.
- Add the estimates for uses that overlap. If the total is more than the first-hour rating, the tank will run short during that hour.
- Check the result with a licensed plumber or your local building department if the numbers are close, because household habits and incoming water temperature change the actual result.
Lowering peak demand is often cheaper than buying a larger tank. Staggering showers, running the dishwasher after the shower, and fixing a leaking hot water faucet can each reduce the total you need to cover. Water heating is about 18% of a home's energy use, according to the U.S. Department of Energy, so efficiency gains from cutting waste also pay off.
Tankless units use a different number
Tankless (on-demand) water heaters do not have a first-hour rating. They are rated by Maximum GPM, which is the maximum gallons per minute of hot water the unit can supply. Sizing a tankless unit starts with the required flow, the sum of the fixtures you use at the same time in gallons per minute, and the temperature rise, which is the desired hot water temperature minus the incoming water temperature.
Do not compare a tankless Maximum GPM with a tank's first-hour rating. They measure different things, and mixing them up is a common reason a new unit disappoints.
Safety and the setting that matters
Set the water heater to 120°F. According to the U.S. Department of Energy, 120°F is considered safe for most of the population, while the Consumer Product Safety Commission notes that third-degree burns can occur after about 5 minutes at 120°F. People with a compromised immune system or chronic respiratory disease may want to keep the setting at 140°F, so check with your doctor first. A higher setting gives more stored hot water, but it also increases scald risk.
Checklist before you buy or size a unit
- Write down the first-hour rating from the label of each tank you are considering.
- Estimate your peak-hour hot water use and compare it with that rating.
- Confirm the unit meets the ENERGY STAR minimum UEF for its type and size.
- Check current federal, state and utility incentives on official sites, because programs change and some have ended.
- Ask your local building department what permits are needed and who pulls them.
- Get at least two written quotes, check the contractor's license with your state licensing board, and ask what is included, such as haul-away, code upgrades and warranty registration.