How often should you flush a water heater?
Many manufacturers recommend flushing a storage (tank) water heater at least once a year, but the owner's manual for your model is the final word. Flushing clears sediment that settles on the tank bottom. Hard water and older tanks can need attention sooner than a fixed calendar suggests.
Why the right interval depends on your water
Sediment comes from minerals in your water supply and from the tank itself. It settles at the bottom, where it can cover the burner or heating element and make the heater work harder to warm the water. Over time that can show up as rumbling or popping noises, slower recovery and less hot water.
Several factors change how fast sediment builds, including water hardness, fuel type, how much hot water your household uses and the age of the tank. Your water utility can usually tell you how hard your supply is. According to the U.S. Department of Energy, most storage water heaters last 10 to 15 years, so an older tank deserves a closer look.
Tankless units do not store water, so there is no tank bottom to drain. Scale can still build up inside them, and the manufacturer's manual gives the descaling method and interval for your unit.
How to flush a storage tank, step by step
Safety first: turn off power at the breaker for an electric unit and confirm it is dead with a voltage tester before you touch anything. Water drained from a tank can scald. The U.S. Consumer Product Safety Commission recommends setting water heaters to 120°F, and third-degree burns can occur after about 5 minutes at that temperature, so let the tank cool before draining it if you can.
- Turn off the power, or set a gas control to pilot or off, following the manual.
- Shut off the cold water supply valve at the top of the tank.
- Open a hot tap somewhere in the house so air can enter the tank and water can drain freely.
- Attach a garden hose to the drain valve at the bottom and run the other end to a floor drain or outdoors where you can see the discharge. Make sure the hose is secured.
- Open the drain valve and let the tank empty. Check that the water runs clear.
- If the water is still cloudy or gritty, close the drain valve, briefly open the cold supply to stir up sediment, then drain again. Repeat until the water runs clear.
- Close the drain valve, remove the hose, and open the cold supply to refill the tank. Close the hot tap once water runs steadily without sputtering.
- Restore power or gas, then check the drain valve and fittings for drips.
Checks to make while the tank is accessible
- Relief valve: the temperature and pressure relief valve must never be capped or plugged. Its discharge pipe should end in an air gap in the same room, no more than 6 inches above the floor or a waste receptor, and it should not be trapped, threaded at the end, or fitted with valves or tees. These rules come from the 2021 International Plumbing Code (section 504.6) and International Residential Code (section P2804.6.1), as summarized by the International Code Council. Codes vary by state and city, so check with your local building department.
- Drain valve: if it drips, sticks or will not close fully after flushing, replace it before the next flush.
- Thermostat: set it to 120°F. The U.S. Department of Energy calls that temperature safe for most people. If someone in the home has a compromised immune system or chronic respiratory disease, the DOE notes they may want 140°F instead. Legionella can grow in water heaters under certain conditions, and according to DOE's FEMP program, a tempering valve set to 120°F downstream of the tank lets the tank run hotter without scald risk at the tap.
- Anode rod: the manual covers inspection timing. Note its condition while the tank is open.
When to stop and call for help
Stop and call for help if the water stays rusty after several rounds of flushing, the drain valve will not seal, the tank leaks, or the relief valve drips steadily. Those problems usually need more than a flush. If you hire a pro, get at least two written quotes, check the contractor's license with your state licensing board where licensing applies, ask who pulls permits, and ask what the price includes, such as haul-away, code upgrades and warranty registration.
Quick checklist before you flush
- Check your model's manual for the recommended flushing and anode inspection intervals.
- Confirm power or gas is off and the cold supply valve is shut.
- Run the hose to a discharge point you can see, and secure it.
- Flush until the water runs clear, then refill and check for leaks.
- Confirm the relief valve discharge pipe still meets the rules listed above.