Does a tankless water heater need maintenance?
Yes. A tankless water heater needs regular maintenance, mainly periodic flushing to clear mineral scale, checking any inlet screen or filter, and following the manufacturer's manual. Many manufacturers recommend flushing at least once a year. Skipped maintenance can reduce hot water output and shorten the unit's service life.
What tankless water heater maintenance involves
Most of the upkeep is about water quality. Minerals in hard water build up as scale inside the heat exchanger, which reduces heating performance over time. Flushing, also called descaling, circulates a cleaning solution through the unit with a pump and isolation valves. The manual for your model sets the exact steps and schedule, and the right interval depends on your water.
Other routine items include cleaning any inlet water filter or screen, since sediment can clog it and cut flow. On gas units, keep vent terminations clear of debris and snow. Electric units have fewer parts that need routine attention, but the manual still lists checks to follow.
Good maintenance helps a unit reach its expected life. According to the U.S. Department of Energy (DOE), most storage (tank) water heaters last 10 to 15 years, while tankless water heaters can last more than 20 years. The U.S. Consumer Product Safety Commission (CPSC) recommends carbon monoxide alarms on every level of the home and outside sleeping areas, which matters for any fuel-burning appliance.
Temperature, scald risk and Legionella
Temperature settings affect both safety and maintenance. The DOE recommends setting a water heater to 120°F, a temperature it considers safe for most of the population. People with a compromised immune system or chronic respiratory disease may want to keep it at 140°F, so ask your doctor before changing the setting.
Hot water can cause serious burns quickly. According to the CPSC, third-degree burns can occur after about 2 seconds at 150°F, about 6 seconds at 140°F, about 30 seconds at 130°F, and after 5 minutes at 120°F. Test the water with your hand before bathing a child or an older adult.
DOE's Federal Energy Management Program notes that Legionella can grow in water heaters under certain conditions. A tempering (mixing) valve set to 120°F, installed downstream of the unit, lets the heater run hotter without raising the temperature at the tap. Ask your installer whether a tempering valve fits your system and how it will be checked.
Flow matters too. Compare your unit's maximum gallons per minute (GPM) rating, which is the most hot water it can supply, against how many fixtures you run at once. Federal maximum flow rates are 2.5 GPM at 80 psi for showerheads and 2.2 GPM at 60 psi for lavatory and kitchen faucets, according to DOE rules at 10 CFR 430.32. If a fixture that used to fill quickly now trickles, scale or a clogged filter is a likely cause, but an undersized unit is another possibility.
Relief valve and discharge pipe
The temperature and pressure relief valve is a safety device, so check its discharge pipe on a regular schedule. The International Plumbing Code 504.6 and International Residential Code P2804.6.1 (2021 editions, as summarized by the International Code Council) describe the pipe. It must not connect directly to the drainage system. It should end in an air gap in the same room, be no smaller than the valve outlet, not be trapped, drain by gravity, and end no more than 6 inches above the floor or a waste receptor.
The discharge pipe must have no threaded end and no valves or tees. The valve is rated for 100 psi at 180°F. A temperature and pressure relief valve must never be capped or plugged. Adoption varies by state and city, so check with your local building department for the rules that apply to you.
Maintenance checklist
- Find the flushing schedule and descaling steps in the manufacturer's manual.
- Flush the unit once a year or as the manual directs, and more often in hard-water areas if the manual allows it.
- Clean the inlet filter or screen, then confirm flow still meets your household's needs.
- Check that the tap water temperature is no higher than you need, typically 120°F for most households.
- Look at the relief valve discharge pipe. It should be unobstructed and drain freely.
- Keep vent terminations clear on gas units, and test your carbon monoxide alarms.
- If you smell gas, leave the home and call the gas utility or 911 from outside.
When flushing, a valve problem or a vent issue goes beyond routine care, get at least two written quotes. Check the contractor's license with your state licensing board where licensing applies, ask who pulls the permits, and ask what the quote includes, such as haul-away, code upgrades and warranty registration.