The Water Heater Guide

Can I take a shower if my water heater is leaking?

Hold off on showering until you know where the water is coming from. A small drip at a fitting can be a simple repair, but a leaking tank, a dripping relief valve or a gas smell means shutting the heater down first. Once the heater is off, you can wash with cold water while you arrange repairs.

Find out where the water is coming from

Water pooling under the tank, or running down the shell from the bottom, usually means the tank itself is failing. According to the U.S. Department of Energy, most storage (tank) water heaters last 10 to 15 years, so an older unit leaking from the tank wall is usually a replacement question rather than a repair question.

Water coming from a pipe connection, the cold inlet or hot outlet fitting, or the shutoff valve is often easier to fix. Dry the area with a towel, place a paper towel under each fitting and check again after a few minutes. If the drip stops or clearly comes from a fitting, the tank may still be sound.

Water from the pipe at the top or side of the heater usually points to the temperature and pressure relief valve. That valve opens to release pressure or heat, so a discharge that keeps running needs a professional to diagnose the cause.

What the relief valve discharge pipe should look like

The discharge pipe is a safety part, not a drain you can seal. The International Plumbing Code (section 504.6) and International Residential Code (section P2804.6.1), 2021 editions as summarized by the International Code Council, describe how it should be built:

  • It must not connect directly to the drainage system.
  • It ends in an air gap in the same room, and it is not smaller than the valve outlet.
  • It must not be trapped, must drain by gravity, and must not have a threaded end, valves or tees.
  • Its end must be no more than 6 inches above the floor or a waste receptor.
  • The valve is rated for 100 psi at 180°F.

A relief valve must never be capped or plugged, even to stop a drip. Codes vary by state and city, so check with your local building department about how your discharge pipe must be run.

Keeping showers safe while you wait for repairs

If the heater is still running, the U.S. Department of Energy recommends setting it to 120°F, a temperature it describes as safe for most of the population. The Consumer Product Safety Commission (CPSC) notes that third-degree burns can occur after about 2 seconds at 150°F, 6 seconds at 140°F, 30 seconds at 130°F, and after about 5 minutes at 120°F.

Hot water supply also drops after a leak, especially if the tank has been partly drained or the heater is shut off. The First-Hour Rating on the unit's label, defined in the federal test procedure (10 CFR 430, Appendix E), estimates how much hot water a storage heater can supply in its first hour starting fully heated. Plan shorter hot showers or stagger use until the heater is repaired or replaced.

Shut down the heater safely

Safety first: if you smell gas, leave the home right away and call the gas utility or 911 from outside. For an electric heater, turn off the breaker, then verify the power is off with a tester before you touch the unit. Never store gasoline or solvents near a gas water heater.

  1. Turn off the power at the breaker for an electric unit, or set the gas control to off or pilot as the label directs for a gas unit.
  2. Close the cold water supply valve on the inlet pipe at the top of the heater.
  3. Open a hot tap in the house to relieve pressure, then leave it open while the tank cools.
  4. Place a pan or bucket under the leak and check it every few hours.
  5. Do not cap, plug or remove the relief valve or its discharge pipe.

Checklist before you shower or call for help

  1. Confirm the leak source: tank wall, fitting, or relief valve discharge.
  2. Shut off power or gas, and close the cold water supply valve.
  3. Check for any gas smell before you go near the unit.
  4. Use cold water or wait if the heater is off and the water is not safe to use hot.
  5. Set the water heater to 120°F once it is running again.
  6. Get at least two written quotes, check the contractor's license with your state licensing board where licensing applies, and ask who pulls the permits.
  7. Ask what is included: haul-away of the old unit, code upgrades, and warranty registration.

Read the full guide →